Preparation

• New Monitor: IX471S*1pcs, firmware version:

• Updated DS: IX850*1pcs , firmware version:

• IP camera: 1~3pcs, standard, onvif, details see below

• PoE Switch: 1~2pcs, standard

• Mobile phone: with VDP connect application, version:

• Network: two different network, one for common, one for private Simulation test

IX850S firmware udpate

IP Camera Applicable instructions and presets

Network requirements for IX471S - What LAN/Wi-Fi infrastructure do I need? （待核实）

others, if interesting（ not necessary ) :

• Mesh Router

• Primary and secondary Router

• WiFi Powerline adaptor

• AC and AP

Demo test for different scenario

Scenario 1 ： Wired Lan connection & common network

This scenario and function are the same as the old version.

The door station IX850 initiates the transfer call, and the monitor IX471S does not need any additional settings except for the basic settings such as Call_Nbr.

tests

for the differences are as follow :

IPS TFT

The screen resolution is better than before, especially when the image is displayed on a HD camera.

Thanks to the IPS screen, the viewing angle is better than the old model.

IP camera

in this scenario,

• connect mode : Settings→Installer→IP Address→IX Net Mode: set to LAN

• divert mode : Manager→SIP config→SIP Network setting: set to LAN

• Settings→Ext.Unit→IPC camera →Add by search//or by manual →chose → input “user name” and “ password” → save

Quad & PiP

Added the functions of monitoring QUAD and incoming call PIP -IP camera setting

PiP （Picture in picture）

Scenario 2 ： Wired Lan connection & private network

In this scenario, users can use their own WiFi .

To success act, must make sure below settings in correct :

1. in monitor:

• connect mode : Settings→Installer→IP Address→IX Net Mode: set to LAN

• connect the Wi-Fi : Settings→Installer→IP Address→Wlan Setting→set the Wi-Fi Switch to ON

  then connect the Wi-Fi by manual or search.

• divert mode : Manager→SIP config→SIP Network setting: set to WLAN

2. connect IP camera

Add by search or Add by manual

• Settings→Ext.Unit→WLAN IPC camera →Add by search//or by manual →chose → input “user name” and “ password” → save

3. test

Scenario 3 : Hybrid Lan & Wlan connection+common network

In this scenario, use common internet and wireless connect monitor to bus

To success act, must make sure below settings in correct :

1. in monitor:

• connect mode: Settings→Installer→IP Address→IX Net Mode: set to WLAN

• connect the Wi-Fi : Settings→Installer→IP Address→Wlan Setting→set the Wi-Fi Switch to ON

  then connect the Wi-Fi by manual or search. ( noted, not the WiFi of home/private but the common)

• divert mode : Manager→SIP config→SIP Network setting: set to WLAN

2. connect IP camera

• Add by search or Add by manual

• Settings→Ext.Unit→IPC camera →Add by search//or by manual →chose → input “user name” and “ password” → save ( for room2 )

• Settings→Ext.Unit→WLAN IPC camera →Add by search//or by manual →chose → input “user name” and “ password” → save ( for room1 )

3. Test

Scenario 4 : Hybrid Lan & Wlan connection+private network

In this scenario, use private network and wireless connect monitor to bus

To success act, must make sure below settings in correct :

1. in monitor:

• connect mode: Settings→Installer→IP Address→IX Net Mode: set to WLAN

• connect the Wi-Fi : Settings→Installer→IP Address→Wlan Setting→set the Wi-Fi Switch to ON

  then connect the Wi-Fi by manual or search. ( noted, not the WiFi of home/private but the common)

• divert mode : Manager→SIP config→SIP Network setting: set to LAN

2. connect IP camera

• Add by search or Add by manual

• Settings→Ext.Unit→IPC camera →Add by search//or by manual →chose → input “user name” and “ password” → save

3. Test