| Table of Contents |
|---|
开锁时间设置
step1. 进入设置状态
DT616上电10s内，按住Call键直到听到3次”BP”音后松开（每秒会响“BP”一声），进入开锁时间设置状态，指示灯慢闪；[此状态维持10s，10s无操作后自动退出]
step2. 设置开锁时间
长按住Call键设置开锁时间，按住的时长=开锁时间，可设置01-99s时间，默认1s；
设置过程中会通过”BP”音提示时间，每响一声为1s；
| Info |
|---|
也可通过分机代码远程设置开锁时间； |
step3. 保存&退出
设置后，无操作10s内自动保存并退出；
设置后，室外机断电自动保存并退出；
开锁模式设置
step1. 进入设置状态
DT616上电10s内，按住Call键直到听到6次”BP”音后松开（每秒会响“BP”一声），进入开锁模式设置状态，指示灯快闪；[此状态维持10s，10s无操作后自动退出]
step2. 设置开锁模式时间
按下Call键来回切换开锁模式；
设置过程中会通过”BP”音提示NC/NO模式，默认NO模式；
| Info |
|---|
也可通过分机代码远程设置开锁模式； |
step3. 保存&退出
设置后，无操作10s内自动保存并退出；
设置后，室外机断电自动保存并退出；
...
设置操作
...
提示音
...
指示灯
...
说明
...
进入开锁时间设置状态
...
响3次BP音
...
慢闪
...
进入开锁模式设置状态
...
响6次BP音
...
快闪
...
开锁时间设置
...
BP音
...
慢闪
...
设置常开NO模式(默认)
...
BP+长音
...
快闪
...
开锁时输出+12V电压
...
设置常闭NC模式
...
BP,BP二声
...
快闪
...
设置后LK+、LK-端口一直输出+12V电压
...
退出设置
...
-
...
常亮
...
...
Unlock Time Setup
Step1. Enter the setup state
Within 10 seconds after power-on, press and hold the Call key until the "BP" sound is heard for 3 times and then release it (the "BP" sound will be heard once per second) to enter the unlocking time setting state, and the indicator light will flash slowly;
| Info |
|---|
This state is maintained for 10 seconds, and automatically exits after 10 seconds of no operation. |
Step2. Set the unlock time
Press and hold the Call key for a long time to set the unlocking time.
The time of pressing and holding is equal to the unlocking time.
The time of 01-99s can be set. The default is 1 s;
In the setting process, the time will be prompted by the "BP" sound, and each sound is 1 s;
| Info |
|---|
The unlocking time can also be set remotely through the monitor with code; |
Step3. Save & Exit
After setting, automatically save and exit within 10s without operation;
or the outdoor unit will automatically save and exit when the power is off;
...
Unlock mode setup
Step1. Enter the setup state
Within 10 seconds after power-on, press and hold the Call key until the "BP" sound is heard for 6 times and then release it (the "BP" sound will be heard once per second) to enter the unlocking mode setting state, and the indicator light will flash quickly;
| Info |
|---|
This state is maintained for 10 seconds, and automatically exits after 10 seconds of no operation. |
Step2. Set Unlock Mode
Press the Call key to switch the unlocking mode back and forth;
The NC/NO mode will be prompted by the "BP" sound during the setting process,
BP + long tone, representing NO,
two tones of BP, representing NC
The defaultand is NO mode
| Info |
|---|
The unlocking mode can also be set remotely through the extension code. |
Step3. Save & Exit
After setting, automatically save and exit within 10s without operation;
or the outdoor unit will automatically save and exit when the power is off;
Setup | Prompt tone | Indicator light | Remark |
|---|---|---|---|
Enter the unlocking time setting state | 3 BPs | Slow flash | |
Enter the unlocking mode setting state | 6 BPs | Quick flash | |
Unlock time setting | BPs | Slow flash | |
Unlock_NO mode | BP + long tone | Quick flash | Output + 12 V when unlocked |
Unlock_NC mode | two tones of BP | Quick flash | After setting, the LK + and LK- ports always output + 12V voltage. |
Exit | - | always on |